![repair manual yashica electro 35 gx repair manual yashica electro 35 gx](http://www.erikfiss.com/foto/cams/electro35/Yashica_Electro_35_Repair_Manual/thumbs/1.jpg)
If you have encountered a camera that has not been in use for a very long time, it is possible that it may contain a battery leakage of such proportions, that the battery cap cannot be unscrewed using an amount of force consistent with not damaging the camera. Rinse with plain water and allow to dry thoroughly. A wooden toothpick will help to get into tight spaces. You want to get rid of all traces of this corrosive residue. Use a sheet of paper to work between the spring contact ring and the surface of the cap. A cotton bud will then clean up the contacts nicely.
![repair manual yashica electro 35 gx repair manual yashica electro 35 gx](https://live.staticflickr.com/65535/50778742226_8f052dbd45_z.jpg)
The battery cap itself can be immersed in vinegar for a while, using a bottle cap or other small container. Be patient! Then daub the area with a clean water bud. You will most likely need to switch ends and use more than one bud to clean this up. With a cotton swab moistened lightly with white vinegar, clean up the spiral spring, or any other internal area where residue can be spotted. If the battery compartment and screw in cap have fallen victim to a battery leak proceed as follows. You can now easily remove light tarnish from the area of the internal spring in the battery compartment with ease. Attach this disk to the eraser end of a pencil using rubber cement or a glue stick. Use a hand or letter punch to cut a small disk out of a sheet of 320 Grit Silicone Carbide Sandpaper.
#Repair manual yashica electro 35 gx professional
Most of what is required to do a professional job may already be within easy reach. Cleaning the internal spring contact area if it doesn't appear to be bright, need not be a challenge either. A shutter with bad lube will only sometimes if ever fire the flash, so you have now pinpointed the most likely cause of the problem.Įlectrical Contact: Establishing a good electrical contact by cleaning the battery compartment screw-in cap is quite straight forward because you have access to it.
#Repair manual yashica electro 35 gx series
In the "G" series of cameras, the flash will not fire until the shutter blades reach their extreme outer travel limit. You do not need film in the camera to wind the shutter. One simple test for this is to attach a strobe flash to the camera, and fire several shots to see if the flash goes off each time. Restoring a snap button face on the camera case.Įrratic Exposure Test: A primary cause of erratic exposure occurs when the lube in the shutter dries and gums up the works. Replacing the original foam light seals which deteriorate, causing many problems. Setting up or reassembling the ASA Speed DialĬleaning or replacing the viewfinder glass Removing the top plate, required for several repairs. Restoring good electrical contact in general and specifically after a battery leak.Ĭhecking the electrical contact between the battery compartment spring and the electronics. You may scroll the page or click on a heading to jump directly to a paragraph.
![repair manual yashica electro 35 gx repair manual yashica electro 35 gx](https://i.ebayimg.com/images/g/6kEAAOSwGJJf23~j/s-l300.jpg)
Copyright to the Text and Images is enforced by me. Trying to change the entire lens assembly often results in a mismatch of electronic parts that you will then need to match up. If you intend to buy a junker for parts, there is an outside chance that even within a specific model, that some parts may appear as slightly different or do not interchange.
![repair manual yashica electro 35 gx repair manual yashica electro 35 gx](https://i.ytimg.com/vi/cvO2a0ikIyQ/maxresdefault.jpg)
None of the information provided here will be found in Yashica's repair manual. Problems with the Electro Rangefinder Camera can frequently be solved that do not require sophisticated test equipment or tools. Servicing Yashica Range-finder Cameras Go to the Site Index